KerbTape
  1. Docs
  2. Getting started

Fund your account in 3 steps

Move USDC to your Hyperliquid account: from Arbitrum, another chain, Bitcoin or an exchange.

On this page

Hyperliquid accounts hold USDC as margin. The funding sheet finds where your money is and shows one route to get it into your Hyperliquid account. It opens by itself when you connect a wallet with an empty account, and from every Deposit button. While your account is empty, the ticket's order button and the one-click bar read Deposit to trade and open this sheet instead of sending an order.

Fund your account in 3 steps · 1:07 · with captions

The three steps#

  1. Where are your funds? The sheet reads your wallet's chain and balances (read only) and suggests a starting point. You can pick another: From a bank or card (the first choice, for money that isn't crypto yet), USDC on Arbitrum, Ethereum, Base, OP Mainnet, Polygon, another EVM chain, Solana, Bitcoin, or An exchange account.
  2. Move them to Hyperliquid. One route, with its typical time and the gas it needs (see the table below). On a phone, the sheet offers to open the step inside your wallet app so the wallet can sign there.
  3. Wait for your deposit. Press I've sent it: wait for it. The sheet checks your Hyperliquid balance (perps and spot) until the money arrives, then takes you to setup or straight back to your order. If nothing has arrived after 30 minutes it says so and points you to the bridge's or the exchange's status page.

Routes#

Your funds are…RouteTypical timeYou need
A bank or cardGet USDC on an exchange you already use, paying from your bank account or card, withdraw it to this same address on the Arbitrum One network (some exchanges can send it straight to Hyperliquid), then deposit it in the terminal. The sheet names exchanges only as examples, in alphabetical order. Step by step: From a bank or broker.The exchange's own times (a first card or bank purchase can take longer), then about a minute.A little ETH on Arbitrum One.
USDC on ArbitrumIn the terminal: your wallet sends USDC to Hyperliquid's own bridge, which credits the same address.Usually under a minute after the transfer confirms.A little ETH on Arbitrum One for gas.
Ethereum, Base, OP Mainnet, Polygon, another EVM chain, SolanaRelay, a third-party bridge listed in Hyperliquid's docs: source = your chain, destination = Hyperliquid, token = Perps USDC. It swaps and bridges in one step.Usually 1–2 minutes.Gas on the source chain. No ETH on Arbitrum.
BitcoinHyperliquid's own Deposit, on Hyperliquid's site, with the same wallet. BTC arrives as spot BTC; swap it for USDC there.Often 20–60 minutes (Bitcoin confirmations).The Bitcoin network fee.
An exchange accountWithdraw USDC to this same address on the Arbitrum One network, then deposit it in the terminal.The exchange's withdrawal time, then about a minute.A little ETH on Arbitrum One.

Minimum deposit

Hyperliquid's bridge doesn't credit deposits under 5 USDC: smaller deposits are lost. Always check that the recipient is your own connected address and, from an exchange, that the network says Arbitrum One.

Where your USDC lands, and the stock markets#

A deposit lands in your main perps balance. What happens next depends on your Hyperliquid account mode:

  • Unified account (the mode Hyperliquid describes as suited to most users): one USDC balance backs perps, spot and the HIP-3 stock markets. Nothing to move.
  • Standard account (every account starts here): main perps, spot and each HIP-3 market group, such as the stock markets on xyz, keep separate USDC balances. The stock markets start at $0. When an order there needs USDC that sits in main perps, the ticket says so and offers two choices instead of an order Hyperliquid would refuse: Move USDC to the stock markets (one wallet signature, prefilled with what the order needs plus a small buffer) or Switch to a unified account (one wallet signature, after a confirm that says what changes, including that a loss on any cross position then draws on the one shared balance).

Either way the USDC stays in your own Hyperliquid account. Nothing moves and no mode changes without your click and your wallet's signature. Move USDC in the account menu moves it back to main perps (or anywhere else among your own balances) at any time. The carry order spends USDC from your spot balance (see carry).

Bridges are run by third parties, not by KerbTape or Hyperliquid. KerbTape never holds your funds at any step.

Updated . These pages describe what the product does. They are not investment advice and say nothing about where any price goes next.